LR-Cal Kalibriergeräte / Calibration Equipment von / from DRUCK & TEMPERATUR Leitenberger - GERMANY

LR-Cal LPP 08 Pressure Test PumpPressure Test Pump
for low pressure and vacuum

Model LR-Cal LPP 08

  • Pneumatic
  • Making pressure to +8 bar (116 psi)
  • Making vaccum to -0.85 bar (-25 inHg)
  • Portable
  • Easy operation

Description

Description Pressure Test Pump LR-Cal LPP 08

The pressure test pump LR-Cal LPP 08 is used to generate pressure and vacuum for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements in the low-pressure and vacuum range. The pressure tests may be carried out in laboratories, workshops or on site at the measuring point.

LR-Cal LPP 08 Pressure Test PumpIf the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the pressure test pump, the same pressure is applied to the two measuring instruments when the pump is operated. By comparing the two measure values at random pressure values, the accuracy can be verified or the unit under test can be adjusted.

The LR-Cal LPP 08 is a pneumatic pressure test pump for low-pressure ranges up to 8 bar with change-over switch to vacuum down to -850 mbar. Despite its compact dimensions, the pressure test pump is easy to operate and allows for exact generation of the required test pressures. The maximum pressure or vacuum achievable depends on the attached test volume. The smooth-running pressure generation and the integrated fine adjustment valve allow a safe and precise setting of very small positive resp. negative pressure values in the range of mbar.

The unit under test and the reference instrument can be easily connected with the supplied accessories.

Included in scope of standard delivery:

  • Pressure test pump LR-Cal LPP 08
  • T-piece, one side with 1/8" BSP male thread for direct mounting to the pressure test pump, other sides with quick hose connectors (Push&Pull) for pneumatic hose 4 x 2 mm. Easy mounting thanks to supplied o-ring. Max. torque 15 Nm.
  • 2 pcs. pneumatic hose 4 x 2 mm, each length 0.5 m
  • 2 pcs. quick connectors (Push&Pull) with 1/8" BSP male thread, for hose 4 x 2 mm
  • 1 Adapter 1/8" BSP female x 1/2" BSP female, for connecting reference instrument (with 1/2" BSP male thread)
    Thanks to integrated o-ring tightening without tools, just by hand
  • 1 Adapter 1/8" BSP female x 1/4" BSP female, for connecting unit under test (with 1/4" BSP male thread)
    Thanks to integrated o-ring tightening without tools, just by hand
  • Operating manual

Options: see "Accessories".

Specification

Specification Pressure Test Pump LR-Cal LPP 08

Pressure generation: 0 to 8 bar = 0 to 116 psi, switchable to
Vacuum generation: 0 to -0.85 bar = 0 to -25 inHg
Pressure ports
(standard version):
For reference measuring instrument:
1/2" BSM female, with o-ring, via hose and t-piece
For unit under test:
1/4" female, with o-ring, via hose and t-piece
Medium: Ambient air
Priming pressure: Ram
High pressure: Volume adjustment valve
Fine pressure adjustment: Volume adjustment valve (very sensitive)
Dimensions: approx. 180 x 111 x 31 mm (without T-piece)
Weight: approx. 295 g (without T-piece)
Order-Code: LPP-08

OEM version without any accessories: Order-Code LPP-08-PUMPE

Accessories

Accessories for Pressure Test Pump LR-Cal LPP 08

Order-Code Description Image
LPP-08-KOFFER ACCESSORY:
Transport and storage case with foams, with space for the pressure test pump plus up to 2 reference measuring instruments, such as LR-Cal LDM 80 or LR-Cal LHM or LR-Cal Serie 2000)
 
LPP-08-T-STUECK SPARE PART:
T-piece with 1/8" BSP male thread for direct mounting to the pressure test pump, with 2 hose connectors (Push&Pull) for pneumatic hose 4 x 2 mm
(Note: 1 pc. included in standard delivery of LR-Cal LPP 08)
T-piece for pressure test pump LR-Cal LPP 08 and pneumatic hose 4 x 2 mm
LPP-08-PN-STECK SPARE PART:
Hose connector (Push&Pull) for hose 4 x 2 mm, with 1/8" BSP male port
(Note: 2 pcs. included in standard delivery of LR-Cal LPP 08)
Hose connector for pneumatic hose 4 x 2 mm
LPP-08-ADAPT-G12 SPARE PART:
Adapter 1/8" BSP female x 1/2" BSP female (for reference measuring instrument) incl. O-ring
(Note: 1 pc. included in standard delivery of LR-Cal LPP 08)
Adapter G 1/2 for pressure test pump LR-Cal LPP 08
LPP-08-ADAPT-G14 SPARE PART:
Adapter 1/8" BSP female x 1/4" BSP female (for test item) incl. O-ring
(Note: 1 pc. included in standard delivery of LR-Cal LPP 08)
Adapter G 1/4 for pressure test pump LR-Cal LPP 08
LPP-08-SCHLAUCH-0050 SPARE PART:
Set of 2 pcs. of pneumatic hose 4 x 2 mm, length 0.5 m
(Note: 1 set included in standard delivery of LR-Cal LPP 08)
Set of 2 pcs. pneumatic hose 4 x 2 mm, length 0.5 m for pressure test pump LR-Cal LPP 08
SET-O-RING-14X3.5 SPARE PART:
Set of 10 pcs. O-ring 14 x 3.5 for reference instrument adapter LPP-08-ADAPT-G12 to be inserted into the 1/2" BSP female thread
Set - 10 pcs. of O-ring 14 x 3.5 for reference instrument adapter for LR-Cal LPP 08
SET-O-RING-8X2.5 SPARE SPART:
Set of 10 pcs. O-ring 8 x 2.5 for test item adapter LPP-08-ADAPT-G14 to be inserted into the 1/4" BSP female thread
Set - 10 pcs. of O-ring 8 x 2.5 for test item adapter for LR-Cal LPP 08
SCHLAUCH-02ID-04AD ACCESSORY:
Pneumatic hose 4 x 2 mm, per meter
 
LPP-ADAPTER-BSP ACCESSORY:
Set of BSP adapters and set of spare o-rings, for test item port: 1/4" BSP male x
1/8" BSP female + 3/8" BSP female + 1/2" BSP female + 1/2" BSP male
Gewindeadaptersatz für LR-Cal Kalibrierhandtestpumpen
LPP-ADAPTER-NPT ACCESSORY:
Set of NPT adapters, for test item port: 1/4" BSP male x
1/8" NPT female + 1/4" NPT female + 3/8" NPT female + 1/2" NPT female
 
LPP-ADAPTER-M ACCESSORY:
Set of metric adapters and set of spare o-rings, for test item port: 1/4" BSP male x
M12x1.5 female + M20x1.5 female + MINIMESS 1620
Metrischer Gewindeadaptersatz für pneumatische LR-Cal Kalibrier-Handtestpumpen, inkl. MINIMESS-Adapter

DOWNLOADs

Datasheet and Manual for Pressure Test Pump LR-Cal LPP 08

Note:
Datasheet and Manual can be downloaded as PDF files. To open PDF files, you need the ADOBE READER. You can get this software free of charge from ADOBE.

Page Top
Page Bottom

Bitte wählen Sie Ihre Sprache:

LR-Cal Leitenberger Kalibriersysteme
is a trade mark of
DRUCK & TEMPERATUR
Leitenberger GmbH

for calibration equipment
Pressure & Temperature.

190x190-lpp60t-tldmm
190x190-lfc80-atc
190x190-lppkit
190x190-lcc100
190x190-llc100
190x190-lpp60-tldmm
190px-ldw-p
190x190-gebaeude32
190x190-fluid200
190x190-lsp-tessnow
190x190-lpp1000
190x190-ldw-hk
190x190-lpp08-koffer
190x190-lpc300-finger
190x190-lcc200
190x190-pulsar
190x190-pyros650
190x190-lhm
190x190-lpp700
190x190-lpp60
190x190-messe1
190x190-lpp08
190x190-gebaeude33
190x190-lfc80-atc-detail
190x190-tldmm
190x190-lsp
190x190-fluid-detail
190x190-messe2
190x190-lhm-drehmoment
190x190-lpc300
190x190-llc100anschluss
190x190-fertigung-2
190x190-lpp40
190x190-lsp1200
190x190-lpp60-koffer
190x190-ldm80
190px-ldw-h
190x190-lhm-kraft
190x190-lfc80
190x190-lsp1000bm-lpc200
190x190-fertigung-1